SFA 1203 Lecture 4: Fuji emulsion lift workshop

instant-university_SFA1203-lecture-4-fuji-emulsion-lift-workshop-title

instant-university_SFA1203-lecture-4-fuji-emulsion-lift-workshop-icon

WHAT’S MOREinstant-university_yellow-border

In this lecture, you will learn about how to do emulsion lift using Fuji instant films. It can be made using FP-100C and 8×10 films. In fact, the process is pretty similar to the Polaroid / Impossible film. The biggest difference between the two is their emulsions. Extra works are needed during the process.

 

WHAT YOU NEEDinstant-university_yellow-border

Instant photo x 1

instant-university_SFA1203-lecture-4-fuji-emulsion-lift-workshop-#1

Scissors x 1

instant-university_SFA1203-lecture-3-polaroid-impossible-emulsion-lift-workshop-#2

Soft paintbrush x 1

instant-university_SFA1203-lecture-4-fuji-emulsion-lift-workshop-#2

Hair-dryer x 1

instant-university_SFA1203-lecture-4-fuji-emulsion-lift-workshop-#3

Tray of hot water (around 70°C / 160°F) x 1

instant-university_SFA1203-lecture-4-fuji-emulsion-lift-workshop-#4

Carrier surface
instant-university_SFA1203-lecture-4-fuji-emulsion-lift-workshop-#5

Acetate x 1

instant-university_SFA1203-lecture-4-fuji-emulsion-lift-workshop-#6

 

STEP-BY-STEPinstant-university_yellow-border

1. After taking a picture, pull film out and wait for like 1.5 minutes for full development. Then you can peel the negative image away from the positive.

2. Air dry the print until it is completely dry. Or use a hairdryer to speed up the drying process.

3. Cut all the white borders around the image.

4. Put the print face up into the hot water. Make sure the print is literally submerged. By rocking the trap back and forward, you will see some white bubbles appear on the image surface, and in about 4 minutes, the emulsion should start falling off from the print.

5. If the emulsion has not completely separating, pour some more hot water and continue the agitation. Use fingers to assist the separation, until the emulsion has totally come off.

6. Take a sheet of acetate and slide it under the emulsion, flatten the lift as much as you can.

7. Put the image on the carrier surface, at this time, the image should be in between of the carrier surface and the acetate.

8. Moisture the carrier with little water, put the acetate over the carrier where you want your image to be.

9. Carefully remove the acetate.

10. Apply the acrylic medium (glass gel medium is fine as well) with a small brush on the image area.

11. Air dry the finishing piece overnight and you are done!

Advertisements

SFA 1203 Lecture 3: Polaroid / Impossible emulsion lift workshop

instant-university_SFA1203-lecture-3-polaroid-impossible-emulsion-lift-workshop-title

instant-university_SFA1203-lecture-3-polaroid-impossible-emulsion-lift-workshop-icon

WHAT IS IT?instant-university_yellow-border

Emulsion lift (also known as emulsion transfer) is an interesting photographic technique. By using this method, you can transfer your image onto a completely different surface like mug, paper, t-shirt, or tote bag, for creative printmaking.

It is all about the jelly-like emulsion layer of instant film being separated from its clear layer. Afterwards, a picture can be reattached to other surface you want. Other than that, you can enlarge or change the shape of the image during the process.

 

WHAT YOU NEEDinstant-university_yellow-border

Instant photo x 1

instant-university_SFA1203-lecture-3-polaroid-impossible-emulsion-lift-workshop-#1

Scissors x 1

instant-university_SFA1203-lecture-3-polaroid-impossible-emulsion-lift-workshop-#2

Soft paintbrush x 2-3

instant-university_SFA1203-lecture-3-polaroid-impossible-emulsion-lift-workshop-#3

Tray of water (in room temperature) x 1

instant-university_SFA1203-lecture-3-polaroid-impossible-emulsion-lift-workshop-#4

Carrier surfaceinstant-university_SFA1203-lecture-3-polaroid-impossible-emulsion-lift-workshop-#5

 

STEP-BY-STEPinstant-university_yellow-border

1. Use scissors to cut the edge off the picture.

2. Remove the whole frame. You will get a square image.

3. Peel the black plastic foil away from the image. 

4. Soak the picture into the water for few minutes.

5. Use a paintbrush to gently brush the image layer (thin emulsion layer) away from the transparent plastic foil in water.

6. Pick the plastic out from the tray. Only keep the emulsion layer in the water. Make sure your image is forward.

7. Take the carrier material you have already prepared. Gently place it underneath the emulsion layer.

8. Carefully position the image layer on top of new surface by using paintbrush. Of course, you can use your fingers for help!

9. Remove the transferred image from water. After it is taken out of the water, you can still create or remove wrinkles and move the image around or even flatten it.

10. Once you finished playing around the shape, let it dry for about 24 hours. The emulsion will stick on the new surface. And you have a Polaroid / Impossible emulsion lift!

 

IMPORTANT NOTEinstant-university_yellow-border

You have to do the emulsion lift within 2 or 3 days after the image is taken. Once the image solidifies, you will no longer be able to separate the layers.

SFA 1203 Lecture 2: After effect – Manipulation by Impossible film

instant-university_SFA1203-lecture-2-manipulation-title

instant-university_SFA1203-lecture-2-manipulation-icon

WHAT IS IT?instant-university_yellow-border

Manipulation is an alternative artistic “painterly effect”. You can convert a normal picture into an Impressionism painting or oil painting! It is very creative, isn’t it?

From old films like Polaroid SX-70 Time Zero or 600 to The Impossible Project. You can create an image with unique result through manipulation, before the emulsion dries.

instant-university_SFA1203-lecture-2-manipulation-#1

“Manipulation makes your Impossible PX70 and PX680 like a little impressionist canvas.” – Carmen Palermo (Credits: The Impossible Project & Carmen Palermo)

 

HOW?instant-university_yellow-border

instant-university_SFA1203-lecture-2-manipulation-#2

Manipulation involves taking a blunt object by applying pressure to a still developing Polaroid. The tools used to the process could be a wooden stick or Cold Clip Pen by Impossible. Sharp tool would ruin the emulsion layer so avoid using it.

instant-university_SFA1203-lecture-2-manipulation-#4

Use pressure to create a blending and slight distortion on the chemicals. Remember, the picture can no longer be restored.

instant-university_SFA1203-lecture-2-manipulation-#3

**Drawing on Impossible film is not as easy as the original Polaroid SX70 film. To do so, it is better for you to heat up the image by hairdryer first and draw harder.